logo de anko
anko I004775 Wi-Fi Smart Pan and Tilt Camera

I004775 Wifi Smart Pan kaj Tilt Fotilo
Uzanto-gvidiloRapida Komenca Gvidilo
Wi-Fi Smart Pan&Tilt Camera
Model I004775
Ŝlosilkodo: 43274604

Pakaj enhavoj

anko I004775 Wi-Fi Smart Pan and Tilt Camera - fig 1


anko I004775 Wi-Fi Smart Pan and Tilt Camera - fig 2
  1. Micro SD card slot (for local storage, max.128GB)
  2. Indika lumo
  3. Fotila lenso
  4. Reset: Press and hold the ‘reset’ for 5 seconds to reset the device
  5. Parolanto
  6. Power: Type-C USB (DC 5V/1A)
  7. Truo por muro pendado
  8. 1/4” Screw hole

Konekta Preparado

anko I004775 Wi-Fi Smart Pan and Tilt Camera - fig 3
anko I004775 Wi-Fi Smart Pan and Tilt Camera - fig 5

It is important that your phone is connected to a 2.4Ghz Wi-Fi and not to a 5GHz network.
To verify your mobile device is set to a 2.4Ghz Wi-Fi network, navigate to the Settings menu and click on Wi-Fi. In this menu you will see all the available networks in your area. Locate the SSID (the name of your network) and ensure that the Wi-Fi SSID does not end with a 5G / 5GHz.Check that you have a strong Wi-Fi signal (at least two bars) in the location where the smart camera is to be installed. anko I004775 Wi-Fi Smart Pan and Tilt Camera - fig 4
Se vi ne havas almenaŭ du stangajn signalojn sur via telefono, tiam vi eble devos rekonsideri transloki la fotilon al alia loko aŭ akiri Wi-Fi-ampleksilon por plifortigi la Wi-Fi-signalon.
Install the Mirabella APP and register Account
To access your camera and it’s functions download the “Mirabella Genio” APP to your smartphone from the App Store or Google Play then add your device to the APP.
Enmetu Micro SD-karton
Please note that the camera will work without an SD card, but it will not be able to record any footage.
Insert the Micro SD card gently into the SD card slot. Please pay attention to the direction of the Micro SD card. Do not force it inside. Micro SD card size needs to be between 8GB and 128Gb, FAT32 format only, This camera doesn’t support NTFS file sistemo.

Parigo de la fotilo per Mirabella Genio App

  1. Power on the camera and wait for the indicator light to start blinking BLUE rapidly. (1 blink every second) if it fails to blink, Use the reset pin provided and insert into the reset port and hold until you hear an audible sound, the camera is now ready to pair.
  2. Check your mobile phone is connected to the 2.4Ghz Wi-Fi network, (Wi-Fi name should not end with -5G).
  3. Open the Mirabella Genio APP, tap on blue “+” icon, then choose add device, then select Security & Sensor and select your camera from the list.anko I004775 Wi-Fi Smart Pan and Tilt Camera - fig 6
  4. Confirm that the LED indicator light is still blinking rapidly blue, tap “confirm Indicator is blinking BLUE rapidly”, then tap “next” and enter your home network 2.4GHz Wi-Fi name and password.anko I004775 Wi-Fi Smart Pan and Tilt Camera - fig 7
anko I004775 Wi-Fi Smart Pan and Tilt Camera - fig 8
anko I004775 Wi-Fi Smart Pan and Tilt Camera - fig 9
anko I004775 Wi-Fi Smart Pan and Tilt Camera - fig 10

Tap next and the QR code will appear on your phone screen, place this QR code in front of the camera at approximate 15-20cm, until you hear a sound,Tap on “Beeped/ Indicator switched” It will then start to connect your device. (refer to the 1st & 2nd images).5. Once the countdown ends, the Camera has now successfully been paired to your APP. Please refer to the FAQ section for troubleshooting if this method does not connect.if somehow the QR code method does not work , please reset and retry using the EZ method.

Oftaj Demandoj

Q. LED indicator is not blinking rapidly as per APP screen

– A. Power off the camera, wait for 20 sec, depress the reset button until you hear a sound, then release the button, wait for another 30-40 sec until the light starts to blink blue rapidly again (1 blink every second).

Q. Fotilo ne skanas la QR-kodon

– A. Please ensure camera is in the pairing mode, indicator light is blinking blue rapidly as per the APP screen, if you are unsure, please simply reset it.

Q. I am using Telstra NBN, I disabled the 5Ghz and still can’t get it to pair?

– A. Please follow the Guest Network paring instructions at https://mirabellagenio.net.au/faqs

Q: Camera will not connect to my Wi-Fi network

– A: Make sure the Wi-Fi network is a 2.4GHz network, device will not connect to a 5GHz network.Also make sure your Wi-Fi name has no space, your Wi-Fi network password is case sensitive, make sure you are entering it correctly.
– Refer to our website’s FAQ and check for your router Is listed as some routers are set up differently.

Q: The camera is off-line

– A: There could be a temporary issue with your internet connection (e.g., service disruption). Please try again in a few minutes. Make sure your Wi-Fi router is turned On.  Make sure the camera is getting a good signal from your Wi-Fi router.
– Use your phone to check range, it is recommended to have at least 2 signal bars showing proper connection.

Q: How to reset the camera to renter pairing mode?

A: Press and hold reset button (see Product Details section) until you hear an audible tone.

Q: Live video stream is slow to load

– A: Camera streaming issues may be caused by any of the following: Your phone’s cellular connection, which relies on mobile overage.Limited internet bandwidth at home, for example, other video streaming services running at the same time on your network can cause congestion slowing down the internet upload and download speeds.Wi-Fi reception may not be stable or work reliably if the camera’s Wi-Fi signal strength is less than 2 signal bars. You may need to install a Wi-Fi repeater or extender to boost the Wi-Fi signal.

Q: The camera is not recording?

– A: Make sure that the microSD card is installed correctly. To confirm the camera is recognizing the microSD card, go to storage Settings in the Settings menu and make sure the microSD
– Card capacity shows Total capacity, Used and Free space. If this does not appear you may consider reformatting the microSD card. WARNING:Reformatting micro SD card will delete all videos stored on card. Once SD card is formatted, your recordings will be stored on the card and can be accessed via the playback button.

Q: What happens when the microSD card reaches full capacity?

– A: Once the microSD card reaches full capacity, new videos will start rewriting (deleting) over the oldest videos.

Q: Kial mi ne povas ricevi la sciigojn per mia poŝtelefona programo?

– A: Confirm that the App has been running on the phone, and the relevant reminder function has been opened; Message notification and authority confirmation in the mobile phone system have been enabled.

anko I004775 Wi-Fi Smart Pan and Tilt Camera - fig 11

How to connect camera to another router
Go to the camera settings page, look for “remove device” Remove it and reset the camera, pair it again to the new router through the app.
Malbona agado, postulas longan tempon ŝarĝi la vivan foontage
Please check the Wi-Fi signal, if it is less than 60%, you will need consider changing the camera location or purchasing a Wi-Fi extender to boost the signal.
Camera went offline and doesn’t reconnect back online by itself
Iru la agordan paĝon de la fotilo, serĉu "forigi aparaton" Forigu ĝin kaj restarigi la fotilon kaj parigu ĝin denove per la programo.
Followed the pairing process but still receive the error Cannot find Device
Manually disable the 5Ghz Wi-Fi signal on the router setting.
Certigu, ke la 2.4Ghz Wi-Fi-signalo estas ŝaltita.
Ensure the indicator light is blinking BLUE rapidly as per APP screen (1 blink per second)
Please check you have entered the correct 2.4Ghz Wi-Fi SSID and password.
I am using Telstra NBN, I disabled 5Ghz and I still cannot get it to pair
Bonvolu sekvi la instrukciojn pri parigo de Gasta Reto https://mirabellagenio.net.au/faqs If you have done all of the above, ensuring that 5Ghz is disabled.
How to turn on or turn off movement notification
On the Genio APP home screen, Tap on Me -> Settings -> App Notification -> turn on/off Enable notifications.
On the iphone, Settings -> Notifications -> turn on/off Allow Notifications for the Mirabella Genio app.
Por multobla fotila agordo, ŝanĝu fotilon view or arrange device set up sequences and manage rooms.
On the genio APP home screen, tap onanko I004775 Wi-Fi Smart Pan and Tilt Camera - icon on the top right corner, to access these options, tap on V to switch below rooms. Tap on x to exit this mode.
Need more help or need further technical assistance from Mirabella engineer
On the genio APP home screen, tap on, Me, -> FAQ & Feedback -> Report issue Fill the fault information or suggestion for the APP/product, then submit

Remember the performance of your Wi-Fi camera is relies heavily on the performance of your router
Se vi uzas Telstra NBN aŭ du-bendan enkursigilon, vi devas malŝalti la 5GHz-Wi-Fi por fari sukcesan konekton kaj por plej bona ĝenerala rendimento, ĉar PLEJ MULTAJ inteligentaj produktoj en Aŭstralio funkcias nur sur la 2.4Ghz-signalo.

logo de anko
anko I004775 Wi-Fi Smart Pan and Tilt Camera - icon 1

Ĉiuj varmarkoj estas uzataj nur por referencaj celoj.
Farita en Ĉinio
Senpaga: 1800 636 528


anko I004775 Wi-Fi Smart Pan and Tilt Camera [pdf] Uzantgvidilo
I004775 Wi-Fi Smart Pan and Tilt Camera, I004775, Wi-Fi Smart Pan and Tilt Camera, Smart Pan and Tilt Camera, Pan and Tilt Camera, Tilt Camera, Camera


lasu komenton

Via retpoŝta adreso ne estos publikigita. Bezonata kampoj estas markitaj *